Jet-tools JWP-208 Manual do Utilizador

Operating Instructions and Parts Manual PlanerModel: JWP-208 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708528Ph.: 800-274-68

102. Check belt tension. Proper tension is obtained when there is approximately 1/4” deflection of the center span of the pulleys using light finger

11The table rollers are factory set for average planing and are parallel to the table surface. If you desire to adjust the table rollers higher or low

12Adjusting Depth of Cut The cutting depth scale (A, Fig. 16) is a combination inch/metric scale with a cutting range from 0 to 8” (204mm). The distan

13lightly backing out the six locking screws (F, Fig. 19) against the slot. NOTE: At this time, only tighten the knife in the slot just enough to hol

14the same manner. 11. After all four knives are set with the screws just snug, back out and tighten the six screws (F) against the slot starting with

15Know the Transmitting Rollers of Your Planer A – Anti-Kickback Fingers B – Infeed Roller C – Chipbreaker D – Cutterhead D – Pressure Bar E – Outfeed

16Figure 25 Height of Infeed Roller, Chipbreaker, Pressure Bar & Outfeed Roller The infeed roller, chipbreaker, pressure bar and outfeed roller ar

17Feed Speed Control Your machine is equipped with a spiral, serrated infeed roller and a solid outfeed roller. When the feed rollers are engaged, the

18MaintenancePeriodic or regular inspections are required to ensure that the machine is in proper adjustment, that all screws are tight, that belts ar

19Figure 32 Figure 33 Figure 34 Figure 35

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servic

20TroubleshootingOperating Problems Problem Possible Cause Solution Snipe.Note: Snipe can be minimized but not eliminated. Table rollers not set prop

21Mechanical and Electrical Problems Problem Possible Cause Solution Uneven depth of cut side to side. Knife projection. Cutterhead not level with be

22Problem Possible Cause Solution Motor failure. Miswiring of the unit. On/off switch failure. is correct, you have a motor problem. If electrical mo

23Head Assembly – Parts List Index Part No. Description Size Qty12 ...BB-6206ZZ...Ball Bearing...

24Head Assembly – Parts List Index Part No. Description Size Qty68 ...6292684 ...Handle...

25Head Assembly – Exploded View

26Table and Roller – Parts and Assembly Index Part No. Description Size Qty1 ...JWP208-201 ...Middle Table...

27Stand and Motor – Parts and Assembly Index Part No. Description Size Qty1 ...JWP208-401 ...Stand...

28Base and Column – Parts List Index Part No. Description Size Qty1 ...JWP208-301 ...Base ...

29Base and Column – Assembly

3Table of ContentsTable of Contents...

30Gearbox – Parts List Index Part No. Description Size Qty1 ...JWP208-501 ...Gear Box ...

31Gearbox – Assembly

32Wiring Diagrams 230V 3HP Single Phase

33 230V 5HP Three Phase

34 460V 5HP Three Phase

35 Notes

37WMH TOOL GROUP2420 Vantage DriveElgin, IL 60123 Ph:800-274-6848www.wmhtoolgroup.com

4WarningsRead the manual. Always read the owner’s manual carefully before attempting to use the machine. Know the limitations and hazards associated w

5Safety Decals Familiarize yourself with the location and content of these decals on your planer. !1. Read instruction manual before operating mac

6FeaturesFig. 2 SpecificationsModel No... JWP-208-1...

7ReceivingCarefully unpack the planer and any loose items from the wood crate and inspect for damage. Any damage should be reported immediately to you

8Handwheel 1. Remove the nut and washer from the gearbox shaft, and place the handwheel onto the shaft (Fig. 5), making sure it is oriented so the ha

9Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes. The machine must be prop