Jet-tools JWP-16OS Manual do Utilizador

1 OWNER’S MANUAL JWP-16OS Woodworking Planer WMH Tool Group Consumer Woodworking Division 2420 Vantage Drive Elgin, IL 60123 Ph: 888-594-5866

10 Figure 2 Starter Box The switch assembly (starter box and bracket) is pre-assembled at the factory and simply needs to be mounted to the head cast

11 Figure 6 Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes. The machine

12Pulleys and Belts The belt and pulley assembly are on the left side of the planer. To inspect for pulley alignment and correct belt tension, remove

13 Figure 13 Table Rollers Two table rollers (A, Fig. 14) ease stock movement as it is fed through the planer. The height of the rollers is dependent

14 Figure 17 Referring to Figure 18 – if adjustment is required: 1. Adjust the tightness of the mounting bolts (A) and the depth of the setscrews (B

15 Planer knives are dangerously sharp. Use extreme caution when inspecting, removing, sharpening, or replacing knives into the cutterhead. Failure t

16the dust port. Remove the cover/dust port (Fig. 20) as a unit. The cutterhead assembly can be seen from the opening on top. Refer to Figure 21: 3.

17 Figure 25 If the gap difference from one side to the other is equal to or less than 0.004", no further adjustment is necessary If the gap dif

18 Figure 27 Transmitting Rollers Figure 28 show the positions of the rollers that are listed below and described in the following sections. A Anti

19 Figure 31 Checking and Adjusting the Feed Roller Height The infeed and outfeed rollers propel the lumber through the planer. The rollers also pre

2This manual has been prepared for the owner and operators of a JET Model JWP-16OS Planer. Its purpose, aside from proper machine operation, is to p

20 Figure 33 Gearbox Referring to Figure 34: The JWP-16OS Planer is equipped with a spiral, serrated infeed roller (F) and a solid outfeed roller. Wh

21 Figure 35 After the head assembly height is adjusted, tighten the two black knobs down again. Power Feed Referring to Figure 36: The power feed fe

22Maintenance General Inspect your planer each time before using. Check for the following conditions and repair or replace when necessary. 1. Loose

23Lubrication The bearings on the cutterhead are factory lubricated and sealed for life – no lubrication required. Gearbox – The oil in the gearbox m

24 Figure 41 Figure 42 Figure 43 Optional Accessories 708814 ...

25Troubleshooting Performance Troubleshooting Problem Possible Cause Solution Table rollers not set properly. Adjust rollers to proper height Inad

26Mechanical Troubleshooting Problem Possible Cause Solution Inadequate tension. Adjust chain tension. Sprockets misaligned. Align sprockets Chain

27Parts List for the JWP-16OS Planer Head Assembly

28Head Assembly Parts List Index No. Part No. Description Size Quantity 1 ...JWP16OS-101 ...Pulley Guard ...

29Head Assembly Parts List Index No. Part No. Description Size Quantity 57 ...JWP15H-007...Screw ...

3Table of Contents Warranty...

30Base Assembly Base Assembly Parts List Index No. Part No. Description Size Quantity 1 ...JWP16OS-201 ...Lifting Handle ...

31Base Assembly Parts List Index No. Part No. Description Size Quantity 18 ...TS-1490041 ...Hex Cap Screw ...

32Gear Box Assembly

33Gear Box Assembly Parts List Index No. Part No. Description Size Quantity 1 ...TS-1550041 ...Flat Washer...

34Stand Assembly Stand Assembly Parts List Index No. Part No. Description Size Quantity 1 ... JWP16OS-401 ...Upper Side Brace

35Electrical Schematic for JWP-16OS Planer

36 WMH TOOL GROUP 2420 Vantage Drive Elgin, IL 60123 Ph: 888-8097-7129 ▪ Fax: 800-274-6840 www.wmhto

4Stand Assembly...

5 Warning 1. Read the manual. Always read the owner’s manual carefully before attempting to use the machine. Know the limitations and hazards associ

6Familiarize yourself with the following safety notices used in this manual. This means that if precautions are not heeded, it may result in serio

7Features of the JWP-16OS Planer Specifications Model Number...

8Receiving Carefully unpack the planer and any loose items from the wood crate and inspect for damage. Any damage should be reported immediately to y

9Assembly Most of the JWP-16OS Planer has been assembled at the factory. However some parts must be assembled after delivery. Use care when cleaning